What's on the HUMMER to-do list?

[alrock]

What do you want or need to get done to the truck?

For me:
Turn front rotors to get rid of warp
Detail the inside as the detail shop did a crappy job on Sunday
Replace cracked center cap - Moab "carnage"
Replace negative battery terminal with something better than OEM
Get a new PCM tune since my PCM was reflashed during the transmission replacement
Get new tires
Wash and wax under the roof rack
Bleed brakes as the fluid has never been fully swapped

 

[Bigunit]

New shocks, front diff skid plate & new torsion bars....maybe wash the T, but I hate to wash it as I have found that washing any vehicle just ruins the paint job...that top layer of mud and grime blocks out all UV & UVB rays and saves the clear coat and metallic base paint...I guess I don't want to wash it after all...maybe after I get back from Moab in April!

 

[Zach]

Steering gear, power steering line. Check upper and lower ball joints. Replace as necessary. Maybe center link. Needs rear shocks. Find the clunk in front end. Diff crossmember when Dwaine comes out with it. ****! I need a lot of money. Wash it? Uh no! Rained here last week

 

[06 H3]

Replace 4 blown shocks replace 2 half shafts as they had bad boots for a while. Get my Ci beefed up front end w locker installed.

Show up the haters. Story with that later...****in jeepers

 

[Big2dabank]

My list is about the same, no special priority...

Fix leaking AC condensor tubes and valves, well this is top priority. I need AC working.
Replace shocks
Replace saggy coil springs, may just add a spacer for now until I figure out what I want to do with the rear.
clean interior, man its filthy dirty
I'm with Zach on the cross member bushing, but waiting for Dwaine for a fix for the H2
I also need to check my steering gear and ps fluid
Fix leak in rear main seal and leaks in the input and output shafts of the transfer case
Fix stripped skid plate bolt, some numb nutz over tightened it
Re-wire my spot lights and also re-wire and re-plumb my air compressor, just need better cable/wire management

 

[cbetts]

Here we go . .

• Redesign entire on-board air system
  • 5 Gallon air tank
  • 100% duty cycle compressor (I am tired of buying new ones. Just blew #3 recently)
  • Ability to disable air tank to allow compressor to fill tires directly
  • Pressure gauge inside
• Redo body mount bolts with LOTS of threadlock
• Straighten right side rock rail
• Wheel alignment (and fix whatever carnage happened at LCC)
• Wire rear roof lights
• Replace CB (current one does not transmit)

 

[cgalpha08]

-Fix my auxiliary lights that hate me and don't want to work.

-Wash and wax (has never been waxed and could use it).

Pretty much it.

Sent from my DROID BIONIC using Tapatalk

 

[3Hummers]

Fill it up

 

[alrock]

• Replace CB (current one does not transmit)

Did you try swapping out the mic yet?

 

[RamRod]

Weld up and assemble the pre-cut slider brackets that I got last week & if I am lucky the tubing for the sliders will get bent up tomorrow as well which mean I can get the sliders completed then mounted up!

 

[LagunaH1]

Replace transfer case
Fix leaking right rear hub
Replace wastegate actuator vacuum line with proper heat resistant line instead of "field fix"
Front end alignment

 

[bebe]

Build/Install a 14 bolt semi float 6- lug rear axle, new drive line and a new windshield

 

[cbetts]

Did you try swapping out the mic yet?

Good one! Not yet but now I will!

 

[twinmill28]

Sell body to science for following repairs--thanks *******s in Congress.....
Rebuild front end---tie rods inner & outer, pitman, idler, steering stab, shocks.
Move 37"s from inside to outside of truck after alignment

 

[06 H3]

Build/Install a 14 bolt semi float 6- lug rear axle, new drive line and a new windshield

front or rear driveline?

 

[poncho1965]

I can't compete.....wash the 3? LOL


Mike

 

[Zach]

I can't compete.....wash the 3? LOL


Mike

I've gotten used to having a tan or brown 2. Ummm yours got washed not that long ago when you had the tcase done. Lmao

 

[bebe]

front or rear driveline?

Rear...wee one - new rear end means new rear DL

 

[poncho1965]

That was the 2nd time this year so that's it


Mike

 

[Zach]

Rear...wee one - new rear end means new rear DL

Oh I'll miss the wee one. You didn't get the memo. He's now the jackal.

And rear end means new rear DL. He's just excited about thinking about what you would create for the front DL. Ya know grease gun in hand excited.

 

[Hunner]

Wheel it!

 

[06 H3]

Oh I'll miss the wee one. You didn't get the memo. He's now the jackal.

And rear end means new rear DL. He's just excited about thinking about what you would create for the front DL. Ya know grease gun in hand excited.

Zach is partially right. I am a jackal after stealing parts off of kyles totaled hummer. Whatever I could easily grab that wasn't destroyed I took before insurance came by to take it.

I know new rear end means new driveline. Yokes change and even distance to t case depending on high pinion vs low pinion. Just wanted to double check that you didn't destroy that massive driveline you already have. I was waiting for pics if that's the case.

He's wrong about the grease gun though, I'm low on grease!!!

 

[f5moab]

Sell....

 

[kflips]

drop it down on the torsion keys about 1/2 inch, new tires soon, go pro camera to replace the contour, new rotors soon, wait for the day that the Moab trips are at a date I can make it before I die and my wife sells the T

 

[Big Mike]

Bump stops and 5100's are next.....

ordered Terra's in a 315 yesterday.. :thumbs:


At some point it needs to go in for window tint..